/* $NetBSD: mha.c,v 1.61 2024/01/07 07:58:33 isaki Exp $ */ /*- * Copyright (c) 1996-1999 The NetBSD Foundation, Inc. * All rights reserved. * * This code is derived from software contributed to The NetBSD Foundation * by Charles M. Hannum, Masaru Oki, Takumi Nakamura, Masanobu Saitoh and * Minoura Makoto. * * Redistribution and use in source and binary forms, with or without * modification, are permitted provided that the following conditions * are met: * 1. Redistributions of source code must retain the above copyright * notice, this list of conditions and the following disclaimer. * 2. Redistributions in binary form must reproduce the above copyright * notice, this list of conditions and the following disclaimer in the * documentation and/or other materials provided with the distribution. * * THIS SOFTWARE IS PROVIDED BY THE NETBSD FOUNDATION, INC. AND CONTRIBUTORS * ``AS IS'' AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED * TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR * PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE FOUNDATION OR CONTRIBUTORS * BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR * CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF * SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS * INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN * CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) * ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE * POSSIBILITY OF SUCH DAMAGE. */ /*- * Copyright (c) 1994 Jarle Greipsland * All rights reserved. * * Redistribution and use in source and binary forms, with or without * modification, are permitted provided that the following conditions * are met: * 1. Redistributions of source code must retain the above copyright * notice, this list of conditions and the following disclaimer. * 2. Redistributions in binary form must reproduce the above copyright * notice, this list of conditions and the following disclaimer in the * documentation and/or other materials provided with the distribution. * 3. The name of the author may not be used to endorse or promote products * derived from this software without specific prior written permission. * * THIS SOFTWARE IS PROVIDED BY THE AUTHOR ``AS IS'' AND ANY EXPRESS OR * IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE * DISCLAIMED. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, * INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, * STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE * POSSIBILITY OF SUCH DAMAGE. */ #include __KERNEL_RCSID(0, "$NetBSD: mha.c,v 1.61 2024/01/07 07:58:33 isaki Exp $"); #include "opt_ddb.h" /* Synchronous data transfers? */ #define SPC_USE_SYNCHRONOUS 0 #define SPC_SYNC_REQ_ACK_OFS 8 /* Default DMA mode? */ #define MHA_DMA_LIMIT_XFER 1 #define MHA_DMA_BURST_XFER 1 #define MHA_DMA_SHORT_BUS_CYCLE 1 #define MHA_DMA_DATAIN (0 | (MHA_DMA_LIMIT_XFER << 1) \ | (MHA_DMA_BURST_XFER << 2) \ | (MHA_DMA_SHORT_BUS_CYCLE << 3)) #define MHA_DMA_DATAOUT (1 | (MHA_DMA_LIMIT_XFER << 1) \ | (MHA_DMA_BURST_XFER << 2) \ | (MHA_DMA_SHORT_BUS_CYCLE << 3)) /* Include debug functions? At the end of this file there are a bunch of * functions that will print out various information regarding queued SCSI * commands, driver state and chip contents. You can call them from the * kernel debugger. If you set SPC_DEBUG to 0 they are not included (the * kernel uses less memory) but you lose the debugging facilities. */ #define SPC_DEBUG 0 /* End of customizable parameters */ /* * MB86601A SCSI Protocol Controller (SPC) routines for MANKAI Mach-2 */ #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include "ioconf.h" #if 0 #define WAIT {if (sc->sc_pc[2]) {printf("[W_%d", __LINE__); while (sc->sc_pc[2] & 0x40);printf("]");}} #else #define WAIT {while (sc->sc_pc[2] & 0x40);} #endif #define SSR (sc->sc_pc[2]) #define SS_IREQUEST 0x80 #define SS_BUSY 0x40 #define SS_DREG_FULL 0x02 #define NSR (sc->sc_pc[3]) #define SIR (sc->sc_pc[4]) #define CMR (sc->sc_pc[5]) #define CMD_SEL_AND_CMD 0x00 #define CMD_SELECT 0x09 #define CMD_SET_ATN 0x0a #define CMD_RESET_ATN 0x0b #define CMD_RESET_ACK 0x0d #define CMD_SEND_FROM_MPU 0x10 #define CMD_SEND_FROM_DMA 0x11 #define CMD_RECEIVE_TO_MPU 0x12 #define CMD_RECEIVE_TO_DMA 0x13 #define CMD_RECEIVE_MSG 0x1a #define CMD_RECEIVE_STS 0x1c #define CMD_SOFT_RESET 0x40 #define CMD_SCSI_RESET 0x42 #define CMD_SET_UP_REG 0x43 #define SCR (sc->sc_pc[11]) #define TMR (sc->sc_pc[12]) #define TM_SYNC 0x80 #define TM_ASYNC 0x00 #define WAR (sc->sc_pc[15]) #define WA_MCSBUFWIN 0x00 #define WA_UPMWIN 0x80 #define WA_INITWIN 0xc0 #define MBR (sc->sc_pc[15]) #define ISCSR (sc->sc_ps[2]) #define CCR (sc->sc_pcx[0]) #define OIR (sc->sc_pcx[1]) #define AMR (sc->sc_pcx[2]) #define SMR (sc->sc_pcx[3]) #define SRR (sc->sc_pcx[4]) #define STR (sc->sc_pcx[5]) #define RTR (sc->sc_pcx[6]) #define ATR (sc->sc_pcx[7]) #define PER (sc->sc_pcx[8]) #define IER (sc->sc_pcx[9]) #define IE_ALL 0xBF #define GLR (sc->sc_pcx[10]) #define DMR (sc->sc_pcx[11]) #define IMR (sc->sc_pcx[12]) #ifndef DDB #define Debugger() panic("should call debugger here (mha.c)") #endif /* ! DDB */ #if SPC_DEBUG #define SPC_SHOWACBS 0x01 #define SPC_SHOWINTS 0x02 #define SPC_SHOWCMDS 0x04 #define SPC_SHOWMISC 0x08 #define SPC_SHOWTRAC 0x10 #define SPC_SHOWSTART 0x20 #define SPC_SHOWPHASE 0x40 #define SPC_SHOWDMA 0x80 #define SPC_SHOWCCMDS 0x100 #define SPC_SHOWMSGS 0x200 #define SPC_DOBREAK 0x400 int mha_debug = #if 0 0x7FF; #else SPC_SHOWSTART|SPC_SHOWTRAC; #endif #define SPC_ACBS(str) do {if (mha_debug & SPC_SHOWACBS) printf str;} while (0) #define SPC_MISC(str) do {if (mha_debug & SPC_SHOWMISC) printf str;} while (0) #define SPC_INTS(str) do {if (mha_debug & SPC_SHOWINTS) printf str;} while (0) #define SPC_TRACE(str) do {if (mha_debug & SPC_SHOWTRAC) printf str;} while (0) #define SPC_CMDS(str) do {if (mha_debug & SPC_SHOWCMDS) printf str;} while (0) #define SPC_START(str) do {if (mha_debug & SPC_SHOWSTART) printf str;}while (0) #define SPC_PHASE(str) do {if (mha_debug & SPC_SHOWPHASE) printf str;}while (0) #define SPC_DMA(str) do {if (mha_debug & SPC_SHOWDMA) printf str;}while (0) #define SPC_MSGS(str) do {if (mha_debug & SPC_SHOWMSGS) printf str;}while (0) #define SPC_BREAK() do {if ((mha_debug & SPC_DOBREAK) != 0) Debugger();} while (0) #define SPC_ASSERT(x) do {if (x) {} else {printf("%s at line %d: assertion failed\n", device_xname(sc->sc_dev), __LINE__); Debugger();}} while (0) #else #define SPC_ACBS(str) #define SPC_MISC(str) #define SPC_INTS(str) #define SPC_TRACE(str) #define SPC_CMDS(str) #define SPC_START(str) #define SPC_PHASE(str) #define SPC_DMA(str) #define SPC_MSGS(str) #define SPC_BREAK() #define SPC_ASSERT(x) #endif int mhamatch(device_t, cfdata_t, void *); void mhaattach(device_t, device_t, void *); void mhaselect(struct mha_softc *, u_char, u_char, u_char *, u_char); void mha_scsi_reset(struct mha_softc *); void mha_reset(struct mha_softc *); void mha_free_acb(struct mha_softc *, struct acb *, int); void mha_sense(struct mha_softc *, struct acb *); void mha_msgin(struct mha_softc *); void mha_msgout(struct mha_softc *); int mha_dataout_pio(struct mha_softc *, u_char *, int); int mha_datain_pio(struct mha_softc *, u_char *, int); int mha_dataout(struct mha_softc *, u_char *, int); int mha_datain(struct mha_softc *, u_char *, int); void mha_abort(struct mha_softc *, struct acb *); void mha_init(struct mha_softc *); void mha_scsi_request(struct scsipi_channel *, scsipi_adapter_req_t, void *); void mha_poll(struct mha_softc *, struct acb *); void mha_sched(struct mha_softc *); void mha_done(struct mha_softc *, struct acb *); int mhaintr(void *); void mha_timeout(void *); void mha_minphys(struct buf *); void mha_dequeue(struct mha_softc *, struct acb *); inline void mha_setsync(struct mha_softc *, struct spc_tinfo *); #if SPC_DEBUG void mha_print_acb(struct acb *); void mha_show_scsi_cmd(struct acb *); void mha_print_active_acb(void); void mha_dump_driver(struct mha_softc *); #endif static int mha_dataio_dma(int, int, struct mha_softc *, u_char *, int); CFATTACH_DECL_NEW(mha, sizeof(struct mha_softc), mhamatch, mhaattach, NULL, NULL); /* * returns non-zero value if a controller is found. */ int mhamatch(device_t parent, cfdata_t cf, void *aux) { struct intio_attach_args *ia = aux; bus_space_tag_t iot = ia->ia_bst; bus_space_handle_t ioh; ia->ia_size=0x20; if (ia->ia_addr != 0xea0000) return 0; if (intio_map_allocate_region(device_parent(parent), ia, INTIO_MAP_TESTONLY) < 0) /* FAKE */ return 0; if (bus_space_map(iot, ia->ia_addr, 0x20, BUS_SPACE_MAP_SHIFTED, &ioh) < 0) return 0; if (!badaddr((void *)IIOV(ia->ia_addr + 0))) return 0; bus_space_unmap(iot, ioh, 0x20); return 1; } /* */ struct mha_softc *tmpsc; void mhaattach(device_t parent, device_t self, void *aux) { struct mha_softc *sc = device_private(self); struct intio_attach_args *ia = aux; tmpsc = sc; /* XXX */ sc->sc_dev = self; aprint_normal(": Mankai Mach-2 Fast SCSI Host Adaptor\n"); SPC_TRACE(("mhaattach ")); sc->sc_state = SPC_INIT; sc->sc_iobase = (void *)IIOV(ia->ia_addr + 0x80); /* XXX */ intio_map_allocate_region(device_parent(parent), ia, INTIO_MAP_ALLOCATE); /* XXX: FAKE */ sc->sc_dmat = ia->ia_dmat; sc->sc_pc = (volatile u_char *)sc->sc_iobase; sc->sc_ps = (volatile u_short *)sc->sc_iobase; sc->sc_pcx = &sc->sc_pc[0x10]; sc->sc_id = IODEVbase->io_sram[0x70] & 0x7; /* XXX */ intio_intr_establish(ia->ia_intr, "mha", mhaintr, sc); mha_init(sc); /* Init chip and driver */ mha_scsi_reset(sc); /* XXX: some devices need this. */ sc->sc_phase = BUSFREE_PHASE; /* * Fill in the adapter. */ sc->sc_adapter.adapt_dev = self; sc->sc_adapter.adapt_nchannels = 1; sc->sc_adapter.adapt_openings = 7; sc->sc_adapter.adapt_max_periph = 1; sc->sc_adapter.adapt_ioctl = NULL; sc->sc_adapter.adapt_minphys = mha_minphys; sc->sc_adapter.adapt_request = mha_scsi_request; sc->sc_channel.chan_adapter = &sc->sc_adapter; sc->sc_channel.chan_bustype = &scsi_bustype; sc->sc_channel.chan_channel = 0; sc->sc_channel.chan_ntargets = 8; sc->sc_channel.chan_nluns = 8; sc->sc_channel.chan_id = sc->sc_id; sc->sc_spcinitialized = 0; WAR = WA_INITWIN; #if 1 CCR = 0x14; OIR = sc->sc_id; AMR = 0x00; SMR = 0x00; SRR = 0x00; STR = 0x20; RTR = 0x40; ATR = 0x01; PER = 0xc9; #endif IER = IE_ALL; /* すべての割り込みを許可 */ #if 1 GLR = 0x00; DMR = 0x30; IMR = 0x00; #endif WAR = WA_MCSBUFWIN; /* drop off */ while (SSR & SS_IREQUEST) { (void) ISCSR; } CMR = CMD_SET_UP_REG; /* setup reg cmd. */ SPC_TRACE(("waiting for intr...")); while (!(SSR & SS_IREQUEST)) delay(10); mhaintr(sc); tmpsc = NULL; config_found(self, &sc->sc_channel, scsiprint, CFARGS_NONE); } #if 0 void mha_reset(struct mha_softc *sc) { u_short dummy; printf("reset..."); CMR = CMD_SOFT_RESET; __asm volatile ("nop"); /* XXX wait (4clk in 20 MHz) ??? */ dummy = sc->sc_ps[-1]; dummy = sc->sc_ps[-1]; dummy = sc->sc_ps[-1]; dummy = sc->sc_ps[-1]; __asm volatile ("nop"); CMR = CMD_SOFT_RESET; sc->sc_spcinitialized = 0; CMR = CMD_SET_UP_REG; /* setup reg cmd. */ while(!sc->sc_spcinitialized); sc->sc_id = IODEVbase->io_sram[0x70] & 0x7; /* XXX */ printf("done.\n"); } #endif /* * Pull the SCSI RST line for 500us. */ void mha_scsi_reset(struct mha_softc *sc) { CMR = CMD_SCSI_RESET; /* SCSI RESET */ while (!(SSR&SS_IREQUEST)) delay(10); } /* * Initialize mha SCSI driver. */ void mha_init(struct mha_softc *sc) { struct acb *acb; int r; if (sc->sc_state == SPC_INIT) { /* First time through; initialize. */ TAILQ_INIT(&sc->ready_list); TAILQ_INIT(&sc->nexus_list); TAILQ_INIT(&sc->free_list); sc->sc_nexus = NULL; acb = sc->sc_acb; memset(acb, 0, sizeof(sc->sc_acb)); for (r = 0; r < sizeof(sc->sc_acb) / sizeof(*acb); r++) { TAILQ_INSERT_TAIL(&sc->free_list, acb, chain); acb++; } memset(&sc->sc_tinfo, 0, sizeof(sc->sc_tinfo)); r = bus_dmamem_alloc(sc->sc_dmat, MAXBSIZE, 0, 0, sc->sc_dmaseg, 1, &sc->sc_ndmasegs, BUS_DMA_NOWAIT); if (r) panic("mha_init: cannot allocate DMA memory"); if (sc->sc_ndmasegs != 1) panic("mha_init: number of segment > 1??"); r = bus_dmamem_map(sc->sc_dmat, sc->sc_dmaseg, sc->sc_ndmasegs, MAXBSIZE, &sc->sc_dmabuf, BUS_DMA_NOWAIT); if (r) panic("mha_init: cannot map DMA memory"); r = bus_dmamap_create(sc->sc_dmat, MAXBSIZE, 1, MAXBSIZE, 0, BUS_DMA_NOWAIT, &sc->sc_dmamap); if (r) panic("mha_init: cannot create dmamap structure"); r = bus_dmamap_load(sc->sc_dmat, sc->sc_dmamap, sc->sc_dmabuf, MAXBSIZE, NULL, BUS_DMA_NOWAIT); if (r) panic("mha_init: cannot load DMA buffer into dmamap"); sc->sc_p = 0; } else { /* Cancel any active commands. */ sc->sc_flags |= SPC_ABORTING; sc->sc_state = SPC_IDLE; if ((acb = sc->sc_nexus) != NULL) { acb->xs->error = XS_DRIVER_STUFFUP; mha_done(sc, acb); } while ((acb = TAILQ_FIRST(&sc->nexus_list)) != NULL) { acb->xs->error = XS_DRIVER_STUFFUP; mha_done(sc, acb); } } sc->sc_phase = sc->sc_prevphase = INVALID_PHASE; for (r = 0; r < 8; r++) { struct spc_tinfo *ti = &sc->sc_tinfo[r]; ti->flags = 0; #if SPC_USE_SYNCHRONOUS ti->flags |= T_SYNCMODE; ti->period = sc->sc_minsync; ti->offset = SPC_SYNC_REQ_ACK_OFS; #else ti->period = ti->offset = 0; #endif ti->width = 0; } sc->sc_state = SPC_IDLE; } void mha_free_acb(struct mha_softc *sc, struct acb *acb, int flags) { int s; s = splbio(); acb->flags = 0; TAILQ_INSERT_HEAD(&sc->free_list, acb, chain); /* * If there were none, wake anybody waiting for one to come free, * starting with queued entries. */ if (TAILQ_NEXT(acb, chain) == NULL) wakeup(&sc->free_list); splx(s); } /* * DRIVER FUNCTIONS CALLABLE FROM HIGHER LEVEL DRIVERS */ /* * Expected sequence: * 1) Command inserted into ready list * 2) Command selected for execution * 3) Command won arbitration and has selected target device * 4) Send message out (identify message, eventually also sync.negotiations) * 5) Send command * 5a) Receive disconnect message, disconnect. * 5b) Reselected by target * 5c) Receive identify message from target. * 6) Send or receive data * 7) Receive status * 8) Receive message (command complete etc.) * 9) If status == SCSI_CHECK construct a synthetic request sense SCSI cmd. * Repeat 2-8 (no disconnects please...) */ /* * Start a selection. This is used by mha_sched() to select an idle target, * and by mha_done() to immediately reselect a target to get sense information. */ void mhaselect(struct mha_softc *sc, u_char target, u_char lun, u_char *cmd, u_char clen) { int i; int s; s = splbio(); /* XXX */ SPC_TRACE(("[mhaselect(t%d,l%d,cmd:%x)] ", target, lun, *(u_char *)cmd)); /* CDB を SPC の MCS REG にセットする */ /* Now the command into the FIFO */ WAIT; #if 1 SPC_MISC(("[cmd:")); for (i = 0; i < clen; i++) { unsigned c = cmd[i]; if (i == 1) c |= lun << 5; SPC_MISC((" %02x", c)); sc->sc_pcx[i] = c; } SPC_MISC(("], target=%d\n", target)); #else memcpy(sc->sc_pcx, cmd, clen); #endif if (NSR & 0x80) panic("scsistart: already selected..."); sc->sc_phase = COMMAND_PHASE; /* new state ASP_SELECTING */ sc->sc_state = SPC_SELECTING; SIR = target; #if 0 CMR = CMD_SELECT; #else CMR = CMD_SEL_AND_CMD; /* select & cmd */ #endif splx(s); } #if 0 int mha_reselect(struct mha_softc *sc, u_char message) { u_char selid, target, lun; struct acb *acb; struct scsipi_periph *periph; struct spc_tinfo *ti; /* * The SCSI chip made a snapshot of the data bus while the reselection * was being negotiated. This enables us to determine which target did * the reselect. */ selid = sc->sc_selid & ~(1 << sc->sc_id); if (selid & (selid - 1)) { printf("%s: reselect with invalid selid %02x; sending DEVICE RESET\n", device_xname(sc->sc_dev), selid); SPC_BREAK(); goto reset; } /* * Search wait queue for disconnected cmd * The list should be short, so I haven't bothered with * any more sophisticated structures than a simple * singly linked list. */ target = ffs(selid) - 1; lun = message & 0x07; TAILQ_FOREACH(acb, &sc->nexus_list, chain) { periph = acb->xs->xs_periph; if (periph->periph_target == target && periph->periph_lun == lun) break; } if (acb == NULL) { printf("%s: reselect from target %d lun %d with no nexus; sending ABORT\n", device_xname(sc->sc_dev), target, lun); SPC_BREAK(); goto abort; } /* Make this nexus active again. */ TAILQ_REMOVE(&sc->nexus_list, acb, chain); sc->sc_state = SPC_HASNEXUS; sc->sc_nexus = acb; ti = &sc->sc_tinfo[target]; ti->lubusy |= (1 << lun); mha_setsync(sc, ti); if (acb->flags & ACB_RESET) mha_sched_msgout(sc, SEND_DEV_RESET); else if (acb->flags & ACB_ABORTED) mha_sched_msgout(sc, SEND_ABORT); /* Do an implicit RESTORE POINTERS. */ sc->sc_dp = acb->daddr; sc->sc_dleft = acb->dleft; sc->sc_cp = (u_char *)&acb->cmd; sc->sc_cleft = acb->clen; return (0); reset: mha_sched_msgout(sc, SEND_DEV_RESET); return (1); abort: mha_sched_msgout(sc, SEND_ABORT); return (1); } #endif /* * Start a SCSI-command * This function is called by the higher level SCSI-driver to queue/run * SCSI-commands. */ void mha_scsi_request(struct scsipi_channel *chan, scsipi_adapter_req_t req, void *arg) { struct scsipi_xfer *xs; struct mha_softc *sc = device_private(chan->chan_adapter->adapt_dev); struct acb *acb; int s, flags; switch (req) { case ADAPTER_REQ_RUN_XFER: xs = arg; SPC_TRACE(("[mha_scsi_cmd] ")); SPC_CMDS(("[0x%x, %d]->%d ", (int)xs->cmd->opcode, xs->cmdlen, xs->xs_periph->periph_target)); flags = xs->xs_control; /* Get a mha command block */ s = splbio(); acb = TAILQ_FIRST(&sc->free_list); if (acb) { TAILQ_REMOVE(&sc->free_list, acb, chain); ACB_SETQ(acb, ACB_QNONE); } if (acb == NULL) { xs->error = XS_RESOURCE_SHORTAGE; scsipi_done(xs); splx(s); return; } splx(s); /* Initialize acb */ acb->xs = xs; memcpy(&acb->cmd, xs->cmd, xs->cmdlen); acb->clen = xs->cmdlen; acb->daddr = xs->data; acb->dleft = xs->datalen; acb->stat = 0; s = splbio(); ACB_SETQ(acb, ACB_QREADY); TAILQ_INSERT_TAIL(&sc->ready_list, acb, chain); #if 1 callout_reset(&acb->xs->xs_callout, mstohz(xs->timeout), mha_timeout, acb); #endif /* * キューの処理中でなければ、スケジューリング開始する */ if (sc->sc_state == SPC_IDLE) mha_sched(sc); splx(s); if (flags & XS_CTL_POLL) { /* Not allowed to use interrupts, use polling instead */ mha_poll(sc, acb); } SPC_MISC(("SUCCESSFULLY_QUEUED")); return; case ADAPTER_REQ_GROW_RESOURCES: /* XXX Not supported. */ return; case ADAPTER_REQ_SET_XFER_MODE: /* XXX Not supported. */ return; } } /* * Adjust transfer size in buffer structure */ void mha_minphys(struct buf *bp) { SPC_TRACE(("mha_minphys ")); minphys(bp); } /* * Used when interrupt driven I/O isn't allowed, e.g. during boot. */ void mha_poll(struct mha_softc *sc, struct acb *acb) { struct scsipi_xfer *xs = acb->xs; int count = xs->timeout * 100; int s; s = splbio(); SPC_TRACE(("[mha_poll] ")); while (count) { /* * If we had interrupts enabled, would we * have got an interrupt? */ if (SSR & SS_IREQUEST) mhaintr(sc); if ((xs->xs_status & XS_STS_DONE) != 0) break; DELAY(10); #if 1 if (sc->sc_state == SPC_IDLE) { SPC_TRACE(("[mha_poll: rescheduling] ")); mha_sched(sc); } #endif count--; } if (count == 0) { SPC_MISC(("mha_poll: timeout")); mha_timeout((void *)acb); } splx(s); scsipi_done(xs); } /* * LOW LEVEL SCSI UTILITIES */ /* * Set synchronous transfer offset and period. */ inline void mha_setsync(struct mha_softc *sc, struct spc_tinfo *ti) { } /* * Schedule a SCSI operation. This has now been pulled out of the interrupt * handler so that we may call it from mha_scsi_cmd and mha_done. This may * save us an unnecessary interrupt just to get things going. Should only be * called when state == SPC_IDLE and at bio pl. */ void mha_sched(struct mha_softc *sc) { struct scsipi_periph *periph; struct acb *acb; int t; SPC_TRACE(("[mha_sched] ")); if (sc->sc_state != SPC_IDLE) panic("mha_sched: not IDLE (state=%d)", sc->sc_state); if (sc->sc_flags & SPC_ABORTING) return; /* * Find first acb in ready queue that is for a target/lunit * combinations that is not busy. */ TAILQ_FOREACH(acb, &sc->ready_list, chain) { struct spc_tinfo *ti; periph = acb->xs->xs_periph; t = periph->periph_target; ti = &sc->sc_tinfo[t]; if (!(ti->lubusy & (1 << periph->periph_lun))) { if ((acb->flags & ACB_QBITS) != ACB_QREADY) panic("mha: busy entry on ready list"); TAILQ_REMOVE(&sc->ready_list, acb, chain); ACB_SETQ(acb, ACB_QNONE); sc->sc_nexus = acb; sc->sc_flags = 0; sc->sc_prevphase = INVALID_PHASE; sc->sc_dp = acb->daddr; sc->sc_dleft = acb->dleft; ti->lubusy |= (1<periph_lun); mhaselect(sc, t, periph->periph_lun, (u_char *)&acb->cmd, acb->clen); break; } else { SPC_MISC(("%d:%d busy\n", periph->periph_target, periph->periph_lun)); } } } /* * POST PROCESSING OF SCSI_CMD (usually current) */ void mha_done(struct mha_softc *sc, struct acb *acb) { struct scsipi_xfer *xs = acb->xs; struct scsipi_periph *periph = xs->xs_periph; struct spc_tinfo *ti = &sc->sc_tinfo[periph->periph_target]; SPC_TRACE(("[mha_done(error:%x)] ", xs->error)); #if 1 callout_stop(&acb->xs->xs_callout); #endif /* * Now, if we've come here with no error code, i.e. we've kept the * initial XS_NOERROR, and the status code signals that we should * check sense, we'll need to set up a request sense cmd block and * push the command back into the ready queue *before* any other * commands for this target/lunit, else we lose the sense info. * We don't support chk sense conditions for the request sense cmd. */ if (xs->error == XS_NOERROR) { if ((acb->flags & ACB_ABORTED) != 0) { xs->error = XS_TIMEOUT; } else if (acb->flags & ACB_CHKSENSE) { xs->error = XS_SENSE; } else { xs->status = acb->stat & ST_MASK; switch (xs->status) { case SCSI_CHECK: xs->resid = acb->dleft; /* FALLTHROUGH */ case SCSI_BUSY: xs->error = XS_BUSY; break; case SCSI_OK: xs->resid = acb->dleft; break; default: xs->error = XS_DRIVER_STUFFUP; #if SPC_DEBUG printf("%s: mha_done: bad stat 0x%x\n", device_xname(sc->sc_dev), acb->stat); #endif break; } } } #if SPC_DEBUG if ((mha_debug & SPC_SHOWMISC) != 0) { if (xs->resid != 0) printf("resid=%d ", xs->resid); if (xs->error == XS_SENSE) printf("sense=0x%02x\n", xs->sense.scsi_sense.response_code); else printf("error=%d\n", xs->error); } #endif /* * Remove the ACB from whatever queue it's on. */ switch (acb->flags & ACB_QBITS) { case ACB_QNONE: if (acb != sc->sc_nexus) { panic("%s: floating acb", device_xname(sc->sc_dev)); } sc->sc_nexus = NULL; sc->sc_state = SPC_IDLE; ti->lubusy &= ~(1<periph_lun); mha_sched(sc); break; case ACB_QREADY: TAILQ_REMOVE(&sc->ready_list, acb, chain); break; case ACB_QNEXUS: TAILQ_REMOVE(&sc->nexus_list, acb, chain); ti->lubusy &= ~(1<periph_lun); break; case ACB_QFREE: panic("%s: dequeue: busy acb on free list", device_xname(sc->sc_dev)); break; default: panic("%s: dequeue: unknown queue %d", device_xname(sc->sc_dev), acb->flags & ACB_QBITS); } /* Put it on the free list, and clear flags. */ #if 0 TAILQ_INSERT_HEAD(&sc->free_list, acb, chain); acb->flags = ACB_QFREE; #else mha_free_acb(sc, acb, xs->xs_control); #endif ti->cmds++; scsipi_done(xs); } void mha_dequeue(struct mha_softc *sc, struct acb *acb) { if (acb->flags & ACB_QNEXUS) { TAILQ_REMOVE(&sc->nexus_list, acb, chain); } else { TAILQ_REMOVE(&sc->ready_list, acb, chain); } } /* * INTERRUPT/PROTOCOL ENGINE */ /* * Schedule an outgoing message by prioritizing it, and asserting * attention on the bus. We can only do this when we are the initiator * else there will be an illegal command interrupt. */ #define mha_sched_msgout(m) \ do { \ SPC_MISC(("mha_sched_msgout %d ", m)); \ CMR = CMD_SET_ATN; \ sc->sc_msgpriq |= (m); \ } while (0) /* * Precondition: * The SCSI bus is already in the MSGI phase and there is a message byte * on the bus, along with an asserted REQ signal. */ void mha_msgin(struct mha_softc *sc) { int v; SPC_TRACE(("[mha_msgin(curmsglen:%d)] ", sc->sc_imlen)); /* * Prepare for a new message. A message should (according * to the SCSI standard) be transmitted in one single * MESSAGE_IN_PHASE. If we have been in some other phase, * then this is a new message. */ if (sc->sc_prevphase != MESSAGE_IN_PHASE) { sc->sc_flags &= ~SPC_DROP_MSGI; sc->sc_imlen = 0; } WAIT; v = MBR; /* modified byte */ v = sc->sc_pcx[0]; sc->sc_imess[sc->sc_imlen] = v; /* * If we're going to reject the message, don't bother storing * the incoming bytes. But still, we need to ACK them. */ if ((sc->sc_flags & SPC_DROP_MSGI)) { CMR = CMD_SET_ATN; /* ESPCMD(sc, ESPCMD_MSGOK);*/ printf("", sc->sc_imess[sc->sc_imlen]); return; } if (sc->sc_imlen >= SPC_MAX_MSG_LEN) { mha_sched_msgout(SEND_REJECT); sc->sc_flags |= SPC_DROP_MSGI; } else { sc->sc_imlen++; /* * This testing is suboptimal, but most * messages will be of the one byte variety, so * it should not effect performance * significantly. */ if (sc->sc_imlen == 1 && MSG_IS1BYTE(sc->sc_imess[0])) goto gotit; if (sc->sc_imlen == 2 && MSG_IS2BYTE(sc->sc_imess[0])) goto gotit; if (sc->sc_imlen >= 3 && MSG_ISEXTENDED(sc->sc_imess[0]) && sc->sc_imlen == sc->sc_imess[1] + 2) goto gotit; } #if 0 /* Ack what we have so far */ ESPCMD(sc, ESPCMD_MSGOK); #endif return; gotit: SPC_MSGS(("gotmsg(%x)", sc->sc_imess[0])); /* * Now we should have a complete message (1 byte, 2 byte * and moderately long extended messages). We only handle * extended messages which total length is shorter than * SPC_MAX_MSG_LEN. Longer messages will be amputated. */ if (sc->sc_state == SPC_HASNEXUS) { struct acb *acb = sc->sc_nexus; struct spc_tinfo *ti = &sc->sc_tinfo[acb->xs->xs_periph->periph_target]; switch (sc->sc_imess[0]) { case MSG_CMDCOMPLETE: SPC_MSGS(("cmdcomplete ")); if (sc->sc_dleft < 0) { struct scsipi_periph *periph = acb->xs->xs_periph; printf("mha: %d extra bytes from %d:%d\n", -sc->sc_dleft, periph->periph_target, periph->periph_lun); sc->sc_dleft = 0; } acb->xs->resid = acb->dleft = sc->sc_dleft; sc->sc_flags |= SPC_BUSFREE_OK; break; case MSG_MESSAGE_REJECT: #if SPC_DEBUG if (mha_debug & SPC_SHOWMSGS) printf("%s: our msg rejected by target\n", device_xname(sc->sc_dev)); #endif #if 1 /* XXX - must remember last message */ scsipi_printaddr(acb->xs->xs_periph); printf("MSG_MESSAGE_REJECT>>"); #endif if (sc->sc_flags & SPC_SYNCHNEGO) { ti->period = ti->offset = 0; sc->sc_flags &= ~SPC_SYNCHNEGO; ti->flags &= ~T_NEGOTIATE; } /* Not all targets understand INITIATOR_DETECTED_ERR */ if (sc->sc_msgout == SEND_INIT_DET_ERR) mha_sched_msgout(SEND_ABORT); break; case MSG_NOOP: SPC_MSGS(("noop ")); break; case MSG_DISCONNECT: SPC_MSGS(("disconnect ")); ti->dconns++; sc->sc_flags |= SPC_DISCON; sc->sc_flags |= SPC_BUSFREE_OK; if ((acb->xs->xs_periph->periph_quirks & PQUIRK_AUTOSAVE) == 0) break; /*FALLTHROUGH*/ case MSG_SAVEDATAPOINTER: SPC_MSGS(("save datapointer ")); acb->dleft = sc->sc_dleft; acb->daddr = sc->sc_dp; break; case MSG_RESTOREPOINTERS: SPC_MSGS(("restore datapointer ")); if (!acb) { mha_sched_msgout(SEND_ABORT); printf("%s: no DATAPOINTERs to restore\n", device_xname(sc->sc_dev)); break; } sc->sc_dp = acb->daddr; sc->sc_dleft = acb->dleft; break; case MSG_PARITY_ERROR: printf("%s:target%d: MSG_PARITY_ERROR\n", device_xname(sc->sc_dev), acb->xs->xs_periph->periph_target); break; case MSG_EXTENDED: SPC_MSGS(("extended(%x) ", sc->sc_imess[2])); switch (sc->sc_imess[2]) { case MSG_EXT_SDTR: SPC_MSGS(("SDTR period %d, offset %d ", sc->sc_imess[3], sc->sc_imess[4])); ti->period = sc->sc_imess[3]; ti->offset = sc->sc_imess[4]; if (sc->sc_minsync == 0) { /* We won't do synch */ ti->offset = 0; mha_sched_msgout(SEND_SDTR); } else if (ti->offset == 0) { printf("%s:%d: async\n", "mha", acb->xs->xs_periph->periph_target); ti->offset = 0; sc->sc_flags &= ~SPC_SYNCHNEGO; } else if (ti->period > 124) { printf("%s:%d: async\n", "mha", acb->xs->xs_periph->periph_target); ti->offset = 0; mha_sched_msgout(SEND_SDTR); } else { #if 0 int p; p = mha_stp2cpb(sc, ti->period); ti->period = mha_cpb2stp(sc, p); #endif #if SPC_DEBUG scsipi_printaddr(acb->xs->xs_periph); #endif if ((sc->sc_flags&SPC_SYNCHNEGO) == 0) { /* Target initiated negotiation */ if (ti->flags & T_SYNCMODE) { ti->flags &= ~T_SYNCMODE; #if SPC_DEBUG printf("renegotiated "); #endif } TMR=TM_ASYNC; /* Clamp to our maxima */ if (ti->period < sc->sc_minsync) ti->period = sc->sc_minsync; if (ti->offset > 15) ti->offset = 15; mha_sched_msgout(SEND_SDTR); } else { /* we are sync */ sc->sc_flags &= ~SPC_SYNCHNEGO; TMR = TM_SYNC; ti->flags |= T_SYNCMODE; } } ti->flags &= ~T_NEGOTIATE; break; default: /* Extended messages we don't handle */ CMR = CMD_SET_ATN; /* XXX? */ break; } break; default: SPC_MSGS(("ident ")); /* thanks for that ident... */ if (!MSG_ISIDENTIFY(sc->sc_imess[0])) { SPC_MISC(("unknown ")); printf("%s: unimplemented message: %d\n", device_xname(sc->sc_dev), sc->sc_imess[0]); CMR = CMD_SET_ATN; /* XXX? */ } break; } } else if (sc->sc_state == SPC_RESELECTED) { struct scsipi_periph *periph = NULL; struct acb *acb; struct spc_tinfo *ti; u_char lunit; if (MSG_ISIDENTIFY(sc->sc_imess[0])) { /* Identify? */ SPC_MISC(("searching ")); /* * Search wait queue for disconnected cmd * The list should be short, so I haven't bothered with * any more sophisticated structures than a simple * singly linked list. */ lunit = sc->sc_imess[0] & 0x07; TAILQ_FOREACH(acb, &sc->nexus_list, chain) { periph = acb->xs->xs_periph; if (periph->periph_lun == lunit && sc->sc_selid == (1<periph_target)) { TAILQ_REMOVE(&sc->nexus_list, acb, chain); ACB_SETQ(acb, ACB_QNONE); break; } } if (!acb) { /* Invalid reselection! */ mha_sched_msgout(SEND_ABORT); printf("mha: invalid reselect (idbit=0x%2x)\n", sc->sc_selid); } else { /* Reestablish nexus */ /* * Setup driver data structures and * do an implicit RESTORE POINTERS */ ti = &sc->sc_tinfo[periph->periph_target]; sc->sc_nexus = acb; sc->sc_dp = acb->daddr; sc->sc_dleft = acb->dleft; sc->sc_tinfo[periph->periph_target].lubusy |= (1<periph_lun); if (ti->flags & T_SYNCMODE) { TMR = TM_SYNC; /* XXX */ } else { TMR = TM_ASYNC; } SPC_MISC(("... found acb")); sc->sc_state = SPC_HASNEXUS; } } else { printf("%s: bogus reselect (no IDENTIFY) %0x2x\n", device_xname(sc->sc_dev), sc->sc_selid); mha_sched_msgout(SEND_DEV_RESET); } } else { /* Neither SPC_HASNEXUS nor SPC_RESELECTED! */ printf("%s: unexpected message in; will send DEV_RESET\n", device_xname(sc->sc_dev)); mha_sched_msgout(SEND_DEV_RESET); } /* Ack last message byte */ #if 0 ESPCMD(sc, ESPCMD_MSGOK); #endif /* Done, reset message pointer. */ sc->sc_flags &= ~SPC_DROP_MSGI; sc->sc_imlen = 0; } /* * Send the highest priority, scheduled message. */ void mha_msgout(struct mha_softc *sc) { #if (SPC_USE_SYNCHRONOUS || SPC_USE_WIDE) struct spc_tinfo *ti; #endif int n; SPC_TRACE(("mha_msgout ")); if (sc->sc_prevphase == MESSAGE_OUT_PHASE) { if (sc->sc_omp == sc->sc_omess) { /* * This is a retransmission. * * We get here if the target stayed in MESSAGE OUT * phase. Section 5.1.9.2 of the SCSI 2 spec indicates * that all of the previously transmitted messages must * be sent again, in the same order. Therefore, we * requeue all the previously transmitted messages, and * start again from the top. Our simple priority * scheme keeps the messages in the right order. */ SPC_MISC(("retransmitting ")); sc->sc_msgpriq |= sc->sc_msgoutq; /* * Set ATN. If we're just sending a trivial 1-byte * message, we'll clear ATN later on anyway. */ CMR = CMD_SET_ATN; /* XXX? */ } else { /* This is a continuation of the previous message. */ n = sc->sc_omp - sc->sc_omess; goto nextbyte; } } /* No messages transmitted so far. */ sc->sc_msgoutq = 0; sc->sc_lastmsg = 0; nextmsg: /* Pick up highest priority message. */ sc->sc_currmsg = sc->sc_msgpriq & -sc->sc_msgpriq; sc->sc_msgpriq &= ~sc->sc_currmsg; sc->sc_msgoutq |= sc->sc_currmsg; /* Build the outgoing message data. */ switch (sc->sc_currmsg) { case SEND_IDENTIFY: SPC_ASSERT(sc->sc_nexus != NULL); sc->sc_omess[0] = MSG_IDENTIFY(sc->sc_nexus->xs->xs_periph->periph_lun, 1); n = 1; break; #if SPC_USE_SYNCHRONOUS case SEND_SDTR: SPC_ASSERT(sc->sc_nexus != NULL); ti = &sc->sc_tinfo[sc->sc_nexus->xs->xs_periph->periph_target]; sc->sc_omess[4] = MSG_EXTENDED; sc->sc_omess[3] = 3; sc->sc_omess[2] = MSG_EXT_SDTR; sc->sc_omess[1] = ti->period >> 2; sc->sc_omess[0] = ti->offset; n = 5; break; #endif #if SPC_USE_WIDE case SEND_WDTR: SPC_ASSERT(sc->sc_nexus != NULL); ti = &sc->sc_tinfo[sc->sc_nexus->xs->xs_periph->periph_target]; sc->sc_omess[3] = MSG_EXTENDED; sc->sc_omess[2] = 2; sc->sc_omess[1] = MSG_EXT_WDTR; sc->sc_omess[0] = ti->width; n = 4; break; #endif case SEND_DEV_RESET: sc->sc_flags |= SPC_ABORTING; sc->sc_omess[0] = MSG_BUS_DEV_RESET; n = 1; break; case SEND_REJECT: sc->sc_omess[0] = MSG_MESSAGE_REJECT; n = 1; break; case SEND_PARITY_ERROR: sc->sc_omess[0] = MSG_PARITY_ERROR; n = 1; break; case SEND_INIT_DET_ERR: sc->sc_omess[0] = MSG_INITIATOR_DET_ERR; n = 1; break; case SEND_ABORT: sc->sc_flags |= SPC_ABORTING; sc->sc_omess[0] = MSG_ABORT; n = 1; break; default: printf("%s: unexpected MESSAGE OUT; sending NOOP\n", device_xname(sc->sc_dev)); SPC_BREAK(); sc->sc_omess[0] = MSG_NOOP; n = 1; break; } sc->sc_omp = &sc->sc_omess[n]; nextbyte: /* Send message bytes. */ /* send TRANSFER command. */ sc->sc_ps[3] = 1; sc->sc_ps[4] = n >> 8; sc->sc_pc[10] = n; sc->sc_ps[-1] = 0x000F; /* burst */ __asm volatile ("nop"); CMR = CMD_SEND_FROM_DMA; /* send from DMA */ for (;;) { if ((SSR & SS_BUSY) != 0) break; if (SSR & SS_IREQUEST) goto out; } for (;;) { #if 0 for (;;) { if ((PSNS & PSNS_REQ) != 0) break; /* Wait for REQINIT. XXX Need timeout. */ } #endif if (SSR & SS_IREQUEST) { /* * Target left MESSAGE OUT, possibly to reject * our message. * * If this is the last message being sent, then we * deassert ATN, since either the target is going to * ignore this message, or it's going to ask for a * retransmission via MESSAGE PARITY ERROR (in which * case we reassert ATN anyway). */ #if 0 if (sc->sc_msgpriq == 0) CMR = CMD_RESET_ATN; #endif goto out; } #if 0 /* Clear ATN before last byte if this is the last message. */ if (n == 1 && sc->sc_msgpriq == 0) CMR = CMD_RESET_ATN; #endif while ((SSR & SS_DREG_FULL) != 0) ; /* Send message byte. */ sc->sc_pc[0] = *--sc->sc_omp; --n; /* Keep track of the last message we've sent any bytes of. */ sc->sc_lastmsg = sc->sc_currmsg; if (n == 0) break; } /* We get here only if the entire message has been transmitted. */ if (sc->sc_msgpriq != 0) { /* There are more outgoing messages. */ goto nextmsg; } /* * The last message has been transmitted. We need to remember the last * message transmitted (in case the target switches to MESSAGE IN phase * and sends a MESSAGE REJECT), and the list of messages transmitted * this time around (in case the target stays in MESSAGE OUT phase to * request a retransmit). */ out: /* Disable REQ/ACK protocol. */ return; } /*************************************************************** * * datain/dataout * */ int mha_datain_pio(struct mha_softc *sc, u_char *p, int n) { u_short d; int a; int total_n = n; SPC_TRACE(("[mha_datain_pio(%p,%d)", p, n)); WAIT; sc->sc_ps[3] = 1; sc->sc_ps[4] = n >> 8; sc->sc_pc[10] = n; /* 悲しきソフト転送 */ CMR = CMD_RECEIVE_TO_MPU; for (;;) { a = SSR; if (a & 0x04) { d = sc->sc_ps[0]; *p++ = d >> 8; if (--n > 0) { *p++ = d; --n; } a = SSR; } if (a & 0x40) continue; if (a & 0x80) break; } SPC_TRACE(("...%d resd]", n)); return total_n - n; } int mha_dataout_pio(struct mha_softc *sc, u_char *p, int n) { u_short d; int a; int total_n = n; SPC_TRACE(("[mha_dataout_pio(%p,%d)", p, n)); WAIT; sc->sc_ps[3] = 1; sc->sc_ps[4] = n >> 8; sc->sc_pc[10] = n; /* 悲しきソフト転送 */ CMR = CMD_SEND_FROM_MPU; for (;;) { a = SSR; if (a & 0x04) { d = *p++ << 8; if (--n > 0) { d |= *p++; --n; } sc->sc_ps[0] = d; a = SSR; } if (a & 0x40) continue; if (a & 0x80) break; } SPC_TRACE(("...%d resd]", n)); return total_n - n; } /* * dw: DMA word * cw: CMR word */ static int mha_dataio_dma(int dw, int cw, struct mha_softc *sc, u_char *p, int n) { char *paddr; if (n > MAXBSIZE) panic("transfer size exceeds MAXBSIZE"); if (sc->sc_dmasize > 0) panic("DMA request while another DMA transfer is in progress"); if (cw == CMD_SEND_FROM_DMA) { memcpy(sc->sc_dmabuf, p, n); bus_dmamap_sync(sc->sc_dmat, sc->sc_dmamap, 0, n, BUS_DMASYNC_PREWRITE); } else { bus_dmamap_sync(sc->sc_dmat, sc->sc_dmamap, 0, n, BUS_DMASYNC_PREREAD); } sc->sc_p = p; sc->sc_dmasize = n; paddr = (char *)sc->sc_dmaseg[0].ds_addr; #if MHA_DMA_SHORT_BUS_CYCLE == 1 if ((*(volatile int *)&IODEVbase->io_sram[0xac]) & (1 << ((paddr_t)paddr >> 19))) dw &= ~(1 << 3); #endif sc->sc_pc[0x80 + (((long)paddr >> 16) & 0xFF)] = 0; sc->sc_pc[0x180 + (((long)paddr >> 8) & 0xFF)] = 0; sc->sc_pc[0x280 + (((long)paddr >> 0) & 0xFF)] = 0; WAIT; sc->sc_ps[3] = 1; sc->sc_ps[4] = n >> 8; sc->sc_pc[10] = n; /* DMA 転送制御は以下の通り。 3 ... short bus cycle 2 ... MAXIMUM XFER. 1 ... BURST XFER. 0 ... R/W */ sc->sc_ps[-1] = dw; /* burst */ __asm volatile ("nop"); CMR = cw; /* receive to DMA */ return n; } int mha_dataout(struct mha_softc *sc, u_char *p, int n) { if (n == 0) return n; if (n & 1) return mha_dataout_pio(sc, p, n); return mha_dataio_dma(MHA_DMA_DATAOUT, CMD_SEND_FROM_DMA, sc, p, n); } int mha_datain(struct mha_softc *sc, u_char *p, int n) { struct acb *acb = sc->sc_nexus; if (n == 0) return n; if (acb->cmd.opcode == SCSI_REQUEST_SENSE || (n & 1)) return mha_datain_pio(sc, p, n); return mha_dataio_dma(MHA_DMA_DATAIN, CMD_RECEIVE_TO_DMA, sc, p, n); } /* * Catch an interrupt from the adaptor */ /* * This is the workhorse routine of the driver. * Deficiencies (for now): * 1) always uses programmed I/O */ int mhaintr(void *arg) { struct mha_softc *sc = arg; #if 0 u_char ints; #endif struct acb *acb; u_char ph; u_short r; int n; #if 1 /* XXX called during attach? */ if (tmpsc != NULL) { SPC_MISC(("[%p %p]\n", mha_cd.cd_devs, sc)); sc = tmpsc; } else { #endif #if 1 /* XXX */ } #endif #if 0 /* * 割り込み禁止にする */ SCTL &= ~SCTL_INTR_ENAB; #endif SPC_TRACE(("[mhaintr]")); /* * 全転送が完全に終了するまでループする */ /* * First check for abnormal conditions, such as reset. */ #if 0 #if 1 /* XXX? */ while (((ints = SSR) & SS_IREQUEST) == 0) delay(1); SPC_MISC(("ints = 0x%x ", ints)); #else /* usually? */ ints = SSR; #endif #endif while (SSR & SS_IREQUEST) { acb = sc->sc_nexus; r = ISCSR; SPC_MISC(("[r=0x%x]", r)); switch (r >> 8) { default: printf("[addr=%p\n" "result=0x%x\n" "cmd=0x%x\n" "ph=0x%x(ought to be %d)]\n", &ISCSR, r, acb->xs->cmd->opcode, SCR, sc->sc_phase); panic("unexpected result."); case 0x82: /* selection timeout */ SPC_MISC(("selection timeout ")); sc->sc_phase = BUSFREE_PHASE; SPC_ASSERT(sc->sc_nexus != NULL); acb = sc->sc_nexus; delay(250); acb->xs->error = XS_SELTIMEOUT; mha_done(sc, acb); continue; /* XXX ??? msaitoh */ case 0x60: /* command completed */ sc->sc_spcinitialized++; if (sc->sc_phase == BUSFREE_PHASE) continue; ph = SCR; if (ph & PSNS_ACK) { int s; /* ふつーのコマンドが終了したらしい */ SPC_MISC(("0x60)phase = %x(ought to be %x)\n", ph & PHASE_MASK, sc->sc_phase)); #if 0 /* switch (sc->sc_phase) {*/ #else switch (ph & PHASE_MASK) { #endif case STATUS_PHASE: if (sc->sc_state != SPC_HASNEXUS) printf("stsin: !SPC_HASNEXUS->(%d)\n", sc->sc_state); SPC_ASSERT(sc->sc_nexus != NULL); acb = sc->sc_nexus; WAIT; s = MBR; SPC_ASSERT(s == 1); __USE(s); acb->stat = sc->sc_pcx[0]; /* XXX */ SPC_MISC(("stat=0x%02x ", acb->stat)); sc->sc_prevphase = STATUS_PHASE; break; case MESSAGE_IN_PHASE: mha_msgin(sc); sc->sc_prevphase = MESSAGE_IN_PHASE; /* thru */ case DATA_IN_PHASE: if (sc->sc_dmasize == 0) break; bus_dmamap_sync(sc->sc_dmat, sc->sc_dmamap, 0, sc->sc_dmasize, BUS_DMASYNC_POSTREAD); memcpy(sc->sc_p, sc->sc_dmabuf, sc->sc_dmasize); sc->sc_dmasize = 0; break; case DATA_OUT_PHASE: if (sc->sc_dmasize == 0) break; bus_dmamap_sync(sc->sc_dmat, sc->sc_dmamap, 0, sc->sc_dmasize, BUS_DMASYNC_POSTWRITE); sc->sc_dmasize = 0; break; } WAIT; CMR = CMD_RESET_ACK; /* reset ack */ /*mha_done(sc, acb); XXX */ continue; } else if (NSR & 0x80) { /* nexus */ #if 1 if (sc->sc_state == SPC_SELECTING) /* XXX msaitoh */ sc->sc_state = SPC_HASNEXUS; /* フェーズの決め打ちをする 外れたら、initial-phase error(0x54) が 返ってくるんで注意したまえ。 でもなぜか 0x65 が返ってきたりしてねーか? */ WAIT; if (SSR & SS_IREQUEST) continue; switch (sc->sc_phase) { default: panic("見知らぬ phase が来ちまっただよ"); case MESSAGE_IN_PHASE: /* 何もしない */ continue; case STATUS_PHASE: sc->sc_phase = MESSAGE_IN_PHASE; CMR = CMD_RECEIVE_MSG; /* receive msg */ continue; case DATA_IN_PHASE: sc->sc_prevphase = DATA_IN_PHASE; if (sc->sc_dleft == 0) { /* 転送データはもうないので ステータスフェーズを期待しよう */ sc->sc_phase = STATUS_PHASE; CMR = CMD_RECEIVE_STS; /* receive sts */ continue; } n = mha_datain(sc, sc->sc_dp, sc->sc_dleft); sc->sc_dp += n; sc->sc_dleft -= n; continue; case DATA_OUT_PHASE: sc->sc_prevphase = DATA_OUT_PHASE; if (sc->sc_dleft == 0) { /* 転送データはもうないので ステータスフェーズを期待しよう */ sc->sc_phase = STATUS_PHASE; CMR = CMD_RECEIVE_STS; /* receive sts */ continue; } /* data phase の続きをやろう */ n = mha_dataout(sc, sc->sc_dp, sc->sc_dleft); sc->sc_dp += n; sc->sc_dleft -= n; continue; case COMMAND_PHASE: /* 最初は CMD PHASE ということらしい */ if (acb->dleft) { /* データ転送がありうる場合 */ if (acb->xs->xs_control & XS_CTL_DATA_IN) { sc->sc_phase = DATA_IN_PHASE; n = mha_datain(sc, sc->sc_dp, sc->sc_dleft); sc->sc_dp += n; sc->sc_dleft -= n; } else if (acb->xs->xs_control & XS_CTL_DATA_OUT) { sc->sc_phase = DATA_OUT_PHASE; n = mha_dataout(sc, sc->sc_dp, sc->sc_dleft); sc->sc_dp += n; sc->sc_dleft -= n; } continue; } else { /* データ転送はないらしい?! */ WAIT; sc->sc_phase = STATUS_PHASE; CMR = CMD_RECEIVE_STS; /* receive sts */ continue; } } #endif } continue; case 0x31: /* disconnected in xfer progress. */ SPC_MISC(("[0x31]")); case 0x70: /* disconnected. */ SPC_ASSERT(sc->sc_flags & SPC_BUSFREE_OK); sc->sc_phase = BUSFREE_PHASE; sc->sc_state = SPC_IDLE; #if 1 acb = sc->sc_nexus; SPC_ASSERT(sc->sc_nexus != NULL); acb->xs->error = XS_NOERROR; mha_done(sc, acb); #else TAILQ_INSERT_HEAD(&sc->nexus_list, acb, chain); mha_sched(sc); #endif continue; case 0x32: /* phase error in xfer progress. */ SPC_MISC(("[0x32]")); #if 0 case 0x65: /* invalid command. なぜこんなものが出るのか 俺には全く理解できない */ #if 1 SPC_MISC(("[0x%04x]", r)); #endif #endif case 0x54: /* initial-phase error. */ SPC_MISC(("[0x54, ns=%x, ph=%x(ought to be %x)]", NSR, SCR, sc->sc_phase)); /* thru */ case 0x71: /* assert req */ WAIT; if (SSR & 0x40) { printf("SPC sts=%2x, r=%04x, ns=%x, ph=%x\n", SSR, r, NSR, SCR); WAIT; } ph = SCR; if (sc->sc_state == SPC_SELECTING) { /* XXX msaitoh */ sc->sc_state = SPC_HASNEXUS; } if (ph & 0x80) { switch (ph & PHASE_MASK) { default: printf("phase = %x\n", ph); panic("assert req: the phase I don't know!"); case DATA_IN_PHASE: sc->sc_prevphase = DATA_IN_PHASE; SPC_MISC(("DATAIN(%d)...", sc->sc_dleft)); n = mha_datain(sc, sc->sc_dp, sc->sc_dleft); sc->sc_dp += n; sc->sc_dleft -= n; SPC_MISC(("done\n")); continue; case DATA_OUT_PHASE: sc->sc_prevphase = DATA_OUT_PHASE; SPC_MISC(("DATAOUT\n")); n = mha_dataout(sc, sc->sc_dp, sc->sc_dleft); sc->sc_dp += n; sc->sc_dleft -= n; continue; case STATUS_PHASE: sc->sc_phase = STATUS_PHASE; SPC_MISC(("[RECV_STS]")); WAIT; CMR = CMD_RECEIVE_STS; /* receive sts */ continue; case MESSAGE_IN_PHASE: sc->sc_phase = MESSAGE_IN_PHASE; WAIT; CMR = CMD_RECEIVE_MSG; continue; } } continue; } } return 1; } void mha_abort(struct mha_softc *sc, struct acb *acb) { acb->flags |= ACB_ABORTED; if (acb == sc->sc_nexus) { /* * If we're still selecting, the message will be scheduled * after selection is complete. */ if (sc->sc_state == SPC_HASNEXUS) { sc->sc_flags |= SPC_ABORTING; mha_sched_msgout(SEND_ABORT); } } else { if (sc->sc_state == SPC_IDLE) mha_sched(sc); } } void mha_timeout(void *arg) { struct acb *acb = (struct acb *)arg; struct scsipi_xfer *xs = acb->xs; struct scsipi_periph *periph = xs->xs_periph; struct mha_softc *sc = device_private(periph->periph_channel->chan_adapter->adapt_dev); int s; s = splbio(); scsipi_printaddr(periph); printf("%s: timed out [acb %p (flags 0x%x, dleft %x, stat %x)], " "", device_xname(sc->sc_dev), acb, acb->flags, acb->dleft, acb->stat, sc->sc_state, sc->sc_nexus, sc->sc_phase, sc->sc_prevphase, sc->sc_dleft, sc->sc_msgpriq, sc->sc_msgout ); printf("[%04x %02x]\n", sc->sc_ps[1], SCR); panic("timeout, ouch!"); if (acb->flags & ACB_ABORTED) { /* abort timed out */ printf(" AGAIN\n"); #if 0 mha_init(sc, 1); /* XXX 1?*/ #endif } else { /* abort the operation that has timed out */ printf("\n"); xs->error = XS_TIMEOUT; mha_abort(sc, acb); } splx(s); } #if SPC_DEBUG /* * The following functions are mostly used for debugging purposes, either * directly called from the driver or from the kernel debugger. */ void mha_show_scsi_cmd(struct acb *acb) { u_char *b = (u_char *)&acb->cmd; struct scsipi_periph *periph = acb->xs->xs_periph; int i; scsipi_printaddr(periph); if ((acb->xs->xs_control & XS_CTL_RESET) == 0) { for (i = 0; i < acb->clen; i++) { if (i) printf(","); printf("%x", b[i]); } printf("\n"); } else printf("RESET\n"); } void mha_print_acb(struct acb *acb) { printf("acb@%p xs=%p flags=%x", acb, acb->xs, acb->flags); printf(" dp=%p dleft=%d stat=%x\n", acb->daddr, acb->dleft, acb->stat); mha_show_scsi_cmd(acb); } void mha_print_active_acb(void) { struct acb *acb; struct mha_softc *sc = device_lookup_private(&mha_cd, 0); /* XXX */ printf("ready list:\n"); TAILQ_FOREACH(acb, &sc->ready_list, chain) mha_print_acb(acb); printf("nexus:\n"); if (sc->sc_nexus != NULL) mha_print_acb(sc->sc_nexus); printf("nexus list:\n"); TAILQ_FOREACH(acb, &sc->nexus_list, chain) mha_print_acb(acb); } void mha_dump_driver(struct mha_softc *sc) { struct spc_tinfo *ti; int i; printf("nexus=%p prevphase=%x\n", sc->sc_nexus, sc->sc_prevphase); printf("state=%x msgin=%x msgpriq=%x msgoutq=%x lastmsg=%x currmsg=%x\n", sc->sc_state, sc->sc_imess[0], sc->sc_msgpriq, sc->sc_msgoutq, sc->sc_lastmsg, sc->sc_currmsg); for (i = 0; i < 7; i++) { ti = &sc->sc_tinfo[i]; printf("tinfo%d: %d cmds %d disconnects %d timeouts", i, ti->cmds, ti->dconns, ti->touts); printf(" %d senses flags=%x\n", ti->senses, ti->flags); } } #endif